lobimlm.blogg.se - Cb radio box 1.5

Jeeps have some unique requirements compared to other vehicles when it comes to picking a CB radio and antenna setup. Without one, how are you going to heckle your buddy two vehicles up for the poor line he just took? Anything smaller is even more ideal.A CB radio is an indispensable tool for any Jeep trail ride. To make for a functional broadcast signal, you need to have a ratio of 1.5:1 at the very minimum. Simply put, the aim we have with testing the channels is to make the readings on both channels as close as possible. Now, repeat those steps for channel “40”. This was a set of processes you perform to take readings.Now, you release the transmit key on the mic.

Now, switch the meter to “Ref” or “SWR” position. Using the knob, you should rotate up until the point the needle reaches the end of the range. Now, we will be adjusting the knob on the meter that says “Set” (sometimes, it says “Adjust” itself).Now, you should turn to the channel “1”.We can now run multiple tests, keeping the microphone the same distance from the SWR meter in each instance, to measure the SWR on different channels: 1 and 40. All that we have done so far enables us to measure the SWR (standing wave ratio: the ratio between the maximum RF voltage to the minimum along a coaxial cable). The actual tuning to get the most accurate readings Now, all you need to do is do the readings and tune accordingly until you get the most accurate reading. This is where you are supposed to input the cable end. Here, look for the marking “XMIT” or “Transmitter”. Now, you should use the jumper lead and connect the SWR meter and your radio.That’s where you are supposed to enter this end. There’s usually a marking “ANT” or “Antenna” on the SWR meter. It will be easy to find the spot where you input this coax cable end into the SWR meter. But here, we plug it into the meter for tuning purposes. This end is going directly to the antenna. Once it’s disconnected from the radio’s back, you should reconnect this end of the coax cable directly to the SWR meter.

How do you do that? Well, you first disconnect the coax (the coaxial cable). It might take a while, so patience is important. Here are the steps you should follow for the correct tuning of your best CB antenna. The steps to correct tuning of your CB radio antenna So, make sure you have a high-quality one for the most accurate reading.

SWR: An SWR meter is the equipment that gets the tuning done.

You all should be inside the vehicle, and the doors must be shut.

People also count: Yes, so you (and if you have friends with you who are helping out) should not hang around the vehicle.

What this means is that you should find a spot where there are no trees, buildings, and other major obstructions about 20 meters from the center of your vehicle.

Plenty of space around the vehicle: You need to have plenty of open space around the vehicle to get an accurate reading.

And what could block your efforts to get that? Well, plenty of stuff. See, the point of tuning is getting the most accurate reading.

The location of the vehicle: It’s very important to find a suitable location for you to park your vehicle where there will be no disturbances for a long period.

Here are the prerequisites that will be necessary if you wish to successfully pull it off: So, now you’re ready to perform a correct tuning for your antenna so that you can work efficiently with your CB radio service. Well, that might have cleared some doubts you had regarding successful CB radio service installation. Ready to start tuning your CB radio antenna? Well, if you want to receive and transmit more than a few feet, you need to tune your antenna. Some people think that once they have set up their CB radio into their car dashboard, got a powerful antenna, and mounted the antenna on a ground plane, they are good to go. And in the next section, I will tell you precisely why is it so. You see, a lot of people, especially those who are new to the entire CB radio service what is and why’s, often make the mistake of thinking that setting up the hardware is all they are going to need to communicate effectively.

If you still haven’t purchased a CB radio, check our guide on the best CB radios.īut before you learn about the correct ways to tune a CB radio antenna, you need to understand the importance of tuning itself. These steps are for the correct tuning, as many people tune incorrectly and then wonder why the signal isn’t powerful enough. Here, we will be going through the right steps to correctly tune your antenna. Tuning a CB radio antenna is important if you want to do anything fruitful with your radio.